Ford Fiesta: Suspension System - General Information / Specifications
Ford Fiesta 2014 - 2019 Service Manual / Suspension / Suspension System - General Information / Specifications
Alignment Specifications — North America
NOTE: All alignment specifications are with the vehicle fuel tank full.
| Item | LH | RH | Split | Thrust Angle |
|---|---|---|---|---|
| Front | ||||
| Camber (Base)a | -0.70° ± 0.75° | -0.70° ± 0.75° | 0.0° ± 0.75° | — |
| Camber (ST)a | -1.18° ± 0.75° | -1.18° ± 0.75° | 0.0° ± 0.75° | — |
| Caster (Base)a | 3.37° ± 0.75° | 3.37° ± 0.75° | 0.0° ± 0.75° | — |
| Caster (ST)a | 3.78° ± 0.75° | 3.78° ± 0.75° | 0.0° ± 0.75° | — |
| Toe (Base) @ curb ride height (positive value is toe in, negative value is toe out) | — | — | 0.15°± 0.20° | — |
| Toe (ST) @ curb ride height (positive value is toe in, negative value is toe out) | — | — | 0.20°± 0.20° | — |
| Rear | ||||
| Camber (Base)a | -1.52° ± 0.75° | -1.52° ± 0.75° | — | — |
| Camber (ST)a | -0.64° ± 1.25° | -0.64° ± 1.25° | — | — |
| Toe (Base) | — | — | — | 0.0° ± 0.50° |
| Toe (ST) | — | — | — | 0.0° ± 0.50° |
aNominal setting (reference only) no adjustment.
Front Wheel Alignment Specifications — South America
NOTE: All alignment specifications are with the vehicle fuel tank full.
| Description | Measurements | Tolerance Range | Setting or Nominal | Maximum Variance Left to Right |
|---|---|---|---|---|
| Caster angle | Degrees and minutes | 2°20' to 4°20' | 3°20' | 1°00' |
| Decimal degrees | 2.34° to 4.34° | 3.34° | 1.00° | |
| Camber angle | Degrees and minutes | -1°-34' to 0°34' | 0°-40' 52" | 1°15' |
| Decimal degrees | -1.56° to 0.57° | -0.68° | 1.25° | |
| Total toe | Degrees and minutes | 0°-9' Toe-in ± 0°33' | 0°12' | - |
| Decimal degrees | -0.15° Toe-in ± 0.55° | 0.2° | - |
Rear Wheel Alignment Specifications — South America
NOTE: All alignment specifications are with the vehicle fuel tank full.
| Description | Measurements | Tolerance Range | Setting or Nominal | Maximum Variance Left to Right |
|---|---|---|---|---|
| Camber angle | Degrees and minutes | -2°46' to -0°16' | -1°31' | 1°25' |
| Decimal degrees | -2.77° to -0.27° | -1.52° | 1.15° | |
| Total toe | Degrees and minutes | 0°4' Toe-in ± 0°34' | Toe-in 0°19' * | - |
| Decimal degrees | 0.06° Toe-in ± 0.56° | Toe-in 0.31° * | - |
*Nominal Setting (For Reference) No Adjustment
General Specifications — North America
| Item | Specification |
|---|---|
| Ball Joint Deflection | |
| Lower | 0-0.2 mm (0-0.008 in) |
| Ride Height | |
| Front (Base) | 16.4 mm (0.646 in) ± 10 mm (0.393 in) |
| Front (ST) | 11.8 mm (0.464 in) ± 14 mm (0.551 in) |
| Rear (Base) | 40.3 mm (1.587 in) ± 10 mm (0.393 in) |
| Rear (ST) | 14.9 mm (0.587 in) ± 14 mm (0.551 in) |
Suspension System. Diagnosis and Testing
Preliminary Inspection
Road test the vehicle.
If any suspension alignment or ride height concerns are present, GO to Symptom Chart — Suspension System...
Other information:
Ford Fiesta 2014 - 2019 Service Manual: Pinpoint Test - DTC: I. Diagnosis and Testing
B007F:11, B007F:12, B007F:13 and B007F:1A Refer to Wiring Diagrams Cell 46 for schematic and connector information. Normal Operation and Fault Conditions The RCM continuously monitors the passenger safety belt retractor pretensioner circuits for the following faults: Resistance out of range Unexpected voltage Short to ground Faulted passe..
Ford Fiesta 2014 - 2019 Service Manual: Halfshaft Bearing - 1.6L EcoBoost (132kW/180PS) – Sigma. Removal and Installation
Special Tool(s) / General Equipment 205-343 (T95P-3514-A) Installer, Constant Velocity Joint Boot ClampTKIT-1995-FTKIT-1995-FM/FLMTKIT-1995-LM/M 205-D064 (D84L-1123-A) Puller, Bearing Flat Headed Screw Driver Hydraulic Press Materials Name Specification Motorcraft® Constant Velocity Joint GreaseXG-5 WSS-M1C258-A1 ..
Categories
- Manuals Home
- Ford Fiesta Service Manual (2014 - 2019)
- Engine System - General Information
- Maintenance Schedules
- Manual Transmission - 6-Speed Manual Transmission – B6
- Front Subframe. Removal and Installation
- Maintenance Schedules - Gasoline Engines. Description and Operation
Ride Height Measurement. General Procedures
Special Tool(s) / General Equipment
Surface GaugeCheck
Ride Height Measurement - Front
NOTE: Make sure that the vehicle is positioned on a flat, level surface and the tires are inflated to the correct pressure. Vehicle should have a full tank of fuel.
Ride height = 2-3Measurement 2
Measurement 3
Use the General Equipment: Surface Gauge
Copyright © 2025 www.fofiesta7.com