Ford Fiesta: Engine Cooling - 1.6L EcoBoost (132kW/180PS) – Sigma / Specifications
Original Fluids
| Name | Fill Capacity |
| Material: Motorcraft® Orange Concentrated Antifreeze/Coolant / VC-3-B (WSS-M97B44-D) | 8.45 qt ( 8 L) |
| Material: Motorcraft® Orange Prediluted Antifreeze/Coolant / VC-3DIL-B (WSS-M97B44-D2) | 8.45 qt ( 8 L) |
Service Fluids and Materials
| Name | Fill Capacity |
| Material: Motorcraft® Yellow Concentrated Antifreeze/Coolant / VC-13-G (WSS-M97B57-A1) | 8.45 qt ( 8 L) |
| Material: Motorcraft® Yellow Prediluted Antifreeze/Coolant / VC-13DL-G (WSS-M97B57-A2) | 8.45 qt ( 8 L) |
| Material: Motorcraft® Premium Cooling System Flush / VC-1 (ESR-M14P7-A) | – |
Antifreeze
| Percent Antifreeze/Coolant to Distilled Water | Freeze Protection |
|---|---|
| 42/58 | -14.8 °F ( -26 °C) |
| 58/42 (Extreme Cold Climates) | -57.9 °F ( -50 °C) |
Cooling System Pressure
| Cooling system pressure test | 150 kPa (21.7 psi) |
| Pressure relief cap | 120 kPa (17.4 psi) to 150 kPa (21.7 psi) |
| Radiator pressure test (removed from vehicle) | 138 kPa (20 psi) |
Thermostat Opening Temperatures
| Starts to open | 82C (180F) |
| Fully open | 97C (207F) |
Engine Cooling - Component Location. Description and Operation
Item
Description
1
Pressure relief cap
2
Degas bottle
3
Coolant pump pulley
4
Coolant pump
5
Thermostat housing
6
Radiator
7
Cooling fan motor and shroud
8
Oil cooler
9
Coolant shutoff solenoid valve
Item
Description
1
Coolant bypass solenoid valve
..
Other information:
Ford Fiesta 2014 - 2019 Service Manual: Heater Core. Removal and Installation
Removal NOTE: Removal steps in this procedure may contain installation details. Remove the heater core and evaporator core housing - vehicles with: EATC and remove the heater core and evaporator core housing - vehicles with: EMTC . Refer to: Heater Core and Evaporator Core Housing - Vehicles With: Electronic Automatic Temperature Control (EATC) (412-00 Climate Control ..
Ford Fiesta 2014 - 2019 Service Manual: Radiator Lower Hose. Removal and Installation
Special Tool(s) / General Equipment Hose Clamp Remover/Installer Removal Drain the cooling system. Refer to: Engine Cooling System Draining, Vacuum Filling and Bleeding (303-03B Engine Cooling - 1.6L EcoBoost (132kW/180PS) – Sigma, General Procedures). Remove the generator. Refer to: Generator - 1.6L EcoBoost (132kW/180PS) – Sigma (414-0..
Categories
- Manuals Home
- Ford Fiesta Service Manual (2014 - 2019)
- Lower Arm. Removal and Installation
- Manual Transmission, Clutch, Transfer Case and Power Transfer Unit
- Engine Component View. Description and Operation
- Engine - 1.6L EcoBoost (132kW/180PS) – Sigma
- Jacking and Lifting - Overview. Description and Operation
Front Strut and Spring Assembly. Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details.
NOTE: This step is only necessary when installing a new component to the left-hand side.
Remove the nuts and position aside the remote brake fluid reservoir.Torque: 62 lb.in (7 Nm)
Remove the strut and spring assembly upper mount nuts. Torque: 22 lb.ft (30 Nm)
Copyright © 2026 www.fofiesta7.com